For Fast Service, Call (864) 905-8566
    Is it possible to install a dimmer switch by yourself

    Is it possible to install a dimmer switch by yourself

    How To: Install a Dimmer Switch

    How to Install a Dimmer Switch

    Photo: Kit Stansley

    I like mood lighting as much as anyone, particularly first thing in the morning when the full blast of light from a 100 watt bulb makes me scream like a vampire at high noon. Could be that I’m just not a morning person. Regardless, I like to be able to adjust the brightness in a room, and installing a dimmer switch is a pretty easy way to get control over your lighting.

    Before you go around ripping switches out of the wall, there are a couple of things you should know about wiring and dimmer switches:

    – Not all dimmer switches are compatible with Compact Fluorescent Lights.  If you have CFL bulbs you will need to go with one of the newer varieties, like those from Lutron.

    – Check to see if the switch you want to replace is a single pole (one switch) or three-way (can be turned on/off from multiple locations) switch—that too will determine the type of dimmer you need.

    – Some dimmer switches use resistors so you’re paying for the electricity even though you’re seeing less light. Newer dimmer switches will actually conserve energy when you’re not lighting the bulb at full capacity.

    What You’ll Need
    Your basic electrical tools will do for this job.
    – Wire strippers
    – Screwdriver
    – Voltage detector (not strictly necessary but highly recommended)
    – Dimmer switch (I prefer the kind that are the same size as a regular toggle switch
    – Flashlight (if you’re working at night or in an area without natural light)

    How to Install a Dimmer Switch - Tools and Materials

    Photo: Kit Stansley


    Step 1: Power Down 
    Not at the switch—at the breaker. This is always at least a three-trip ordeal for me… down to the basement, flip the breaker, up to test the switch, over and over again. However, it beats sticking your hand into a live circuit any day. I always use a voltage detector before touching any wires.

    How to Install a Dimmer Switch - Voltage Detector

    Photo: Kit Stansley

    Step 2: Out With The Old
    Once everything is shut off, unscrew the old switch and pull everything out so you can get a good look at it. For a toggle switch like this, the wires are more than likely wrapped around the connector screws. Either loosen the screws or use the wire strippers to snip the ends off and remove the old switch.

    Step 3: Install the Dimmer 
    To install the dimmer, read the instructions to make sure you’re clear on what wires go where and which is the top and which is the bottom. As always, green denotes the ground or copper wire. Unlike installing a light fixture, both wires going to the dimmer will be black and usually can be placed on either gold screw. There shouldn’t be any silver screws.

    How to Install a Dimmer Switch - Out with Old

    Photo: Kit Stansley

    If the switch can be used for either a single-pole or three-way, there may be an extra screw so make sure to look at the wiring diagram. (In this case it was covered by tape so it was very clear which was the “extra” connection.)

    Note: On this dimmer’s directions it said you could just insert the wire straight under the screw, rather than loop it around, and tighten the connection. But an electrician friend of mine says he always loops the wire if possible, as he’s seen too many cases where the wire pulls loose. So looping it is!

    To connect the wires, strip 3/4″ of casing off the end, loop it into a U shape, hook it around the screw, and then pinch the ends together before tightening the screw down.

    How to Install a Dimmer Switch - Putting It Together

    Photo: Kit Stansley

    Step 4: Putting It Back Together 
    Once the wires are attached, you will want to re-fasten the switch to the electrical box with two screws top and bottom, and then re-attach the switch plate.

    How to Install a Dimmer Switch - Complete

    Photo: Kit Stansley

    Turn the breaker back on, and there you have it… ultimate control over the brightness in one small section of the universe!


    Full Service Residential & Commercial Carpet Cleaning in Greenville SC

    As a licensed, insured and bonded company, Superior Carpet Cleaning And Repair uses modern carpet care technologies and preparations to ensure the lowest level of toxicity. For your convenience, we cover a 50 mile radius. You can trust us to clean your furniture too. Our professional upholstery cleaning service is well known among our residential and commercial customers. Take advantage of our Greer, SC specialists’ skills and qualifications to protect your rugs. No job is too difficult or too complicated for us!

    Close Menu